5.) Yamaha

HSD-X Glue dispenser

Vintage 2000

L to R, rear fixed

0.09 sec

S/N : Y6777

Excellent condition

Location : Penang

6.) KME SP10P-MA printer

S/N : 108Z0007

Auto Vision

L to R, rear fixed

M size, max PCB size 330mmX250mm

Squeegee speed 10 – 150mm/sec

Speed per print 17sec

Vintage : 1994/95    

7.) Electro Vert Model Omniflo Oven,

Type OMNI7, 7 heating zones, 2 cooling zones

S/N : M0950824075(1995)

440 V, 82 KVA, 3-Phase, 60

Wire mesh and rail

L to R, front fixed

N2

Fully refurbished

8.) BTU TRS212-8-140GT Reflow oven

S/N : TBI-5

8 heating zones, 2 cooling zones

Vintage 1996

Left to Right, front fixed

Wire mesh with edge rail

N2

9.) Eight Tech AIS301 oven, left to right, front fixed

10.) KME RF10A-MA oven, left to right rear fixed

11.)Antom Oven

Serial # 94-04-795

Model : SOLSYS-300IRX

3 phase, 200V 81 AMP 28KVA

Right to Left,  front fixed

5 zones

Convection

Vintage 94

12.) Electrovert 650C/F Wave Solder;

Computer control

20” maximum allowable width

Dual, Lamda and Chip waves

3 bottom convection preheaters;

One IR top heater;

N2

wave fluxer

440v/3ph/60 hz;

S/N 11871905

Vintage : 1997

13.) Electrovert 650C/F Wave Solder;

Computer control

20” maximum allowable width

Dual, Lamda and Chip waves

3 Convection Preheaters;

One IR top heater;

N2

wave fluxer

440v/3ph/60 hz;

S/N 11870197

Vintage : 1997

14.) Electrovert 650M/F Wave Solder;

20” maximum allowable width

Dual, Lamda and Chip waves

 3 Convection Preheaters; N2

USI Spray Fluxer;

440v/3ph/52.2kva;

S/N MO960212041

Vintage : 1996

15.) Electrovert 660M/F Wave Solder;

24” maximum allowable width

Dual, Lamda and Chip waves

Foam fluxer

3 Bottom Side Convection Preheaters; N2;

440v/3ph/83kva;

S/N 11870684

Vintage : 1997

16.) Speedline Electrovert Opti-flux

Vintage 12/2000

S/N : 931101404

Excellent condition

17.) Cyberoptics Sentry 2000

June 1997     serial #350019      @1

Technical spec. :

-         3D profiling/ true volume measurement

-         Solder paste repeatability 2 micron

-         Max board size : 460mm X 560mm

-         Max field of view : 9.0 X 6.7mm

-         Depth of view : +/-2mm

-         Typical inspection speed : 0.75 sec

-         Weight 500 lbs

 

18.) SVS 8100 3D laser solder paste inspection machine, 2 units available

Technical Spec. :

-          for precise height and volumetric measurements, the best indicators of final solder joint quality.

-          Small Footprint, High Reliability System

-          Optimized for High-Throughput Solder Paste Inspection; Also Performs Component Placement Inspection 

-          Meets the Most Demanding Cycle Time Requirements with 100% Inspection

-          Industry's Best Inspection Data Accuracy and Repeatability via Patented 3-D Scanning Laser

-          Off-Line Programming & CAD Support Software for Simplified Setup

-          Real-Time Statistical Process Control

-          Easy-to-Use, Configurable Operator Interface Requires Minimal Operator Training

19.) Conceptronics HGR Freedom 2000 BGA rework station

S/N : FR20045 and FR20037(2 units)

Vintage : 1996

Lab condition, hardly used

Board Handling Capacity
• 2 inch x 2 inch (5 cm x 5 cm) minimum recommended board size
• 20 inch x 18 inch (50.8 cm x 45.7 cm) maximum recommended board size
• Able to repair boards with up to 1.5 inch (38 mm) tall components
• PCB Thickness’ up to 0.25 inch (6.4 mm)

Component Handling Capacity
• 0.25 inch (6.4 mm) square minimum recommended component size
• 2-inch (51 mm) square maximum recommended component size
• Handles both grid array and leaded type components. (BGA, CGA, QFP, LCC, TSOP,FLIP-CHIP, and many others)
• Placement Accuracy to 0.001 inches

20.) Systemation ST-495(Tape and reel)

Vintage : Nov 1997

S/N : 795000110

Software : ST-495.EXE

Voltage : 220V/single phase

80 PSI,  30 amp

Tray to Tape and tape to tray

21.) Loader    @2

22.) Unloader @2

23.) Conveyors – various sizes

24.) Feeders